Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterAmarr Cable & Drum Replacement: The Hollywood Owner’s Guide
Amarr cable and drum replacement in Hollywood typically runs $130-$250 installed, and we carry Amarr-compatible cables and drums on our trucks for same-day service in most cases. Most Hollywood homeowners discover the failure the same way: the door suddenly hangs crooked, makes a grinding noise halfway up, or one side drops faster than the other when the opener pulls. The cable has either snapped, slipped off the drum, or the drum itself has worn to the point where it no longer winds the cable evenly. We quote a flat, written price before any work starts, and every job closes with a documented photo record of what we found and what we replaced.
Which Amarr Models This Applies To
Amarr builds doors under several series lines: the Lincoln, Heritage, Olympus, Stratford, and Classica collections are the ones we see most often in Hollywood residential garages. Each series uses a specific cable length and drum profile, and the two are matched as a pair. The quickest way to identify your door is the model label on the inside of the top section or the end stile, which lists the part number and door size. If the label is worn off, we measure the cable diameter with a caliper during the visit. Amarr residential doors typically use 1/8-inch or 3/32-inch aircraft-grade steel cable, and the drums are cast aluminum or nylon depending on the series year.
On the OEM versus aftermarket question: Amarr OEM cables and drums are built to the exact drum taper and cable length spec for your door, and we recommend them for doors under warranty or doors with an unusual height (8-foot and 10-foot Hollywood garage ceilings are common in newer construction near Sheridan Street and the Lakes). Quality aftermarket equivalents work fine for standard 7-foot doors, but there is one compatibility gotcha worth knowing. Amarr drums on some Classica models use a different keyway slot width than generic drums, so a universal drum can bind on the torsion tube. We verify the keyway measurement before quoting. Servo Garage Doors Hollywood is an independent service provider, not affiliated with Amarr, and we stock parts for Amarr along with LiftMaster, Chamberlain, and Genie openers.
Signs Your Amarr Cable & Drum Replacement Is Failing
- The door hangs uneven or crooked when lifting. One cable has stretched, frayed, or slipped off its drum, which means the non-lifting side is carrying zero tension. This is the single most common early warning sign in Hollywood garages, where summer humidity accelerates cable oxidation.
- You hear a scraping or popping sound near the top of the track. The cable is binding inside a worn drum groove or jumping out of the groove entirely. Every cycle with that bind wears the cable strands down further.
- The cable looks frayed, rusted, or has visible broken strands. Aircraft cable fails by losing strands one at a time before the full snap. If you see loose strands near the bottom bracket, the cable is already past its service life.
- One side of the door drops hard when the opener disengages. That means a cable let go entirely and the door is now off-balance, with the remaining spring and cable holding the full load. Do not keep cycling the door in this condition.
- The door stops lifting a few inches up and reverses. A drum may have stripped its set screws and is spinning on the torsion tube, so the cable is not winding or unwinding with the shaft. The opener senses the uneven resistance and backs off.
BeforeAfterReplacement Cost & What’s Included
Amarr cable and drum replacement in Hollywood ranges from $130 to $250 installed, with the spread driven by whether we are replacing one cable, a cable and drum pair, or both sides, and whether your door is a standard 7-foot or taller 8-foot model. The price is parts plus labor with no hidden lines, and we quote it as a flat, written number before any work starts. That is Clause 1 of The Haven Standard: a written price and written scope delivered before the first tool comes off the truck. You will also receive a documented photo record of the failed cable and drum before we quote the replacement, per Clause 4. Our work on the parts we install is covered by the 365-Day Done Right Promise, and the price you see on the written quote is the price on the invoice. If another company has already quoted you and you want a second look, bring us the paperwork and we will review it at no charge.
DIY or Call Us?
You can safely inspect an Amarr cable and drum from the ground without touching anything under tension. Look for rust, frayed strands, or a cable that has jumped out of its drum groove. What you should not do is attempt to re-seat a cable or replace a drum yourself. The torsion tube on an Amarr door holds a wound spring that can release hundreds of pounds of rotational force if the set screws are loosened improperly. Every experienced technician has seen the aftermath of a bar slipping out of a winding cone. We are not trying to scare anyone off from basic maintenance; we are telling you plainly that cable and drum work on a torsion system belongs to a trained professional. If you are unsure whether what you are looking at needs a pro, call us at (754) 465-7645 and describe what you see. We will tell you over the phone whether it is worth a service call.
FAQs
Amarr cables and drums generally last 7 to 10 years in Hollywood, though homes within a few miles of the Intracoastal or the ocean often see cables fail earlier, sometimes in 5 to 7 years, because salt air accelerates steel oxidation even inside a closed garage. The drum itself is aluminum or nylon and usually outlasts one or two cable sets, unless the door has been cycling out of balance for a while. If you live east of US-1, expect to inspect cables more often. For an exact quote on your door, call (754) 465-7645.
No, a frayed or rusted Amarr cable cannot be repaired; cables are replaced, never spliced or patched, because a splice under garage-door tension is a failure waiting to happen. Drums are sometimes reusable if the grooves are clean and the keyway is intact, but a drum with stripped set screws or worn grooves gets replaced. We always show you the part that failed and the condition it was in before we quote, so you are not taking our word alone. Call (754) 465-7645 and we will walk you through what we typically find on your Amarr model.
Most Amarr cable and drum replacements take 45 to 90 minutes on site for a single side, and 90 minutes to two hours if both sides and both drums are worn and being replaced together. The work includes re-balancing the door and running a minimum of five full test cycles before we close the job. We carry Amarr-compatible cables and drums on the truck, so the swap typically is completed same day without a second visit. Call (754) 465-7645 to schedule a time window, and we will send you a text with the technician’s name before arrival.
Yes, we stock Amarr-compatible cables and drums for the common 7-foot and 8-foot residential series, Lincoln, Heritage, Olympus, Stratford, and Classica, on our Hollywood service trucks. For less common configurations, we can have the OEM or matched aftermarket part in hand within one to two business days. If you can send a photo of the model label on the inside of your door, we can confirm exact part availability before we roll a truck. Call (754) 465-7645 and our live dispatcher will get it sorted, any time of day.
Call Servo Garage Doors Hollywood
If your Amarr door is hanging crooked, grinding at the top of the track, or showing a frayed cable, call (754) 465-7645. We will quote a flat, written price for the cable and drum replacement before any work begins, and you will receive a documented photo record of the failed part when we arrive. Marcus Deller and our Hollywood-based crew stand behind every job with the 365-Day Done Right Promise. Name the part, quote the range, then do the work.
Written by Marcus Deller, Owner, Servo Garage Doors Hollywood at Servo Garage Doors Hollywood, serving Hollywood and nearby areas.