Raynor Cable & Drum Replacement Nationwide

Raynor Cable & Drum Replacement: The Hollywood Owner’s Guide

We stock and install Raynor-compatible cable and drum assemblies, with a typical installed price of $130 to $250 for cable replacement in Hollywood, FL, and $250 to $500 when the drum assembly requires replacement as a paired set. Most Raynor cable failures we see are same-day fixes, since the parts travel on our trucks. The usual story: the door jerks on the way up, then sags visibly to one side. You look up, and there’s a frayed cable or, worse, a loose cable hanging from the drum. That’s the moment to stop using the door, unplug the opener, and call a tech who can photograph the failed part before quoting a dollar figure. Marcus Deller and our crew have been pulling into Hollywood driveways for this exact failure for years, and the diagnosis is rarely a surprise: Florida humidity plus daily cycles equals cable fatigue.

Call (754) 465-7645

Which Raynor Models This Applies To

Raynor builds steel and aluminum residential doors across several series: the Aspen AP200, Centura, ProMaster, Advantage, and older Reliant and Pacesetter lines still found in Hollywood homes from the 1990s and early 2000s. Cable length and drum profile are the two specs that matter most, and they vary between models and door heights. A 7-foot door and an 8-foot door use different cable lengths, and the drum’s groove count has to match the cable diameter. Here’s the compatibility gotcha we see often: a Raynor drum may look close to a generic one, but the taper angle is model-specific. The wrong drum means the door rides unevenly and the new cable wears out in six months. We check the model label on the door edge, then verify the cable length from the old part. For Raynor, we use OEM parts when the customer prefers exact factory spec, and quality aftermarket equivalents when the OEM part is backordered. We’ll show you both prices before anything is installed. Servo Garage Doors Hollywood is an independent service provider and not affiliated with Raynor. We also stock parts for LiftMaster, Chamberlain, and Genie openers, because half the time a door problem starts at the opener rail and travels down.

Signs Your Raynor Cable & Drum Replacement Is Failing

• Door tilts or sags on one side during travel. This means one cable has stretched or begun to fray while the other still holds full tension. The drum on the weak side is often skipping a groove when you watch it with the opener in manual mode.
• Frayed steel strands visible near the bottom bracket. Cables fail at the attachment point first, where the loop connects to the bottom fixture. In Hollywood’s salt-adjacent air, corrosion accelerates this and makes the fray easy to spot even at arm’s length.
• Clattering or popping sounds from above the header. A cable that has jumped the drum will slap against the drum face and the horizontal track as the door cycles. If you hear this, stop cycling the door. The remaining cable is now carrying the full load.
• Door stops about a foot from the floor on the way down. This is classic for a broken cable. The door jams because one side loses tension and the other cable pulls it into a bind against the track. Forcing it open or closed can fold the section.
• Visible gap between the drum and the cable. When a Raynor drum’s grooves wear past spec, the cable seats shallow and can slide off the drum entirely. We see this on doors with 10 or more years of daily use, particularly ones that were never serviced for roller wear.

Before

After

Replacement Cost & What’s Included

The installed cable replacement price in Hollywood runs $130 to $250, and a full drum set replacement runs $250 to $500 depending on the Raynor model and whether both sides are replaced. Here’s the number that matters: the written quote is flat and delivered before we touch a bolt. Clause 1 of The Haven Standard means no surprises after the fact. The price includes the specific part we’re installing, the labor, a full track and roller inspection, and a load test on the spring system. If we find the torsion spring measured out of spec, we’ll photograph it and show you the reading before recommending a spring replacement, which is a separate line item on the same written quote and runs $180 to $340 in Hollywood. The work carries our 365-Day Done Right Promise. If the cable or drum fails within that first year, we make it right. Every visit closes with a documented photo record of what was removed and what was installed. You see the failed part. You see the new part. You keep the record.

DIY or Call Us?

Safety first, with no softening: garage door cables carry spring tension, and a cable under load can whip across a garage or take off a finger if it lets go while you’re working the drum. This is not a YouTube job. What an owner can safely do is identify the failure: visually inspect for frayed strands, check if the door is tilted in the track, and photograph the area. Then stop. Attempting to re-spool a cable onto a drum without releasing spring tension is how emergency room visits happen. The professional route takes about 45 to 90 minutes, includes the photo record, and ends with Marcus’s one non-negotiable: five full test cycles before we close the invoice. If you’re in Hollywood and the cable is already broken, call (754) 465-7645. We’ll name the part, quote the range, then do the work.

FAQs