Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterWayne Dalton Garage Door Installation in Hollywood: What to Know First
Wayne Dalton garage door installation in Hollywood typically runs $700-$2,200, depending on door size, material, and whether you’re replacing an existing Wayne Dalton unit or starting fresh. As an independent Wayne Dalton service provider, we install and service the full range of Wayne Dalton residential doors across Hollywood, most jobs completed within three to five business days of measure. We quote every installation with a flat, written price before any work begins, per Clause 1 of The Haven Standard, so there’s no guessing when the invoice arrives.
This page is for Hollywood homeowners who own a Wayne Dalton door that’s reached the end of its service life, or who are considering Wayne Dalton for a new installation and want to know what actually holds up in South Florida’s salt air and humidity. If you have a door that won’t open, a panel that’s buckling, or you’re comparing Wayne Dalton against Clopay or Amarr, you’ll find the specifics below. Call (754) 465-7645 and you’ll get a live person, not a recording.
How Wayne Dalton Products Fail - and How We Fix Them
- TorqueMaster spring failure on the 8000 and 9000 series. Wayne Dalton’s TorqueMaster system houses the torsion spring inside a sealed tube, which is different from the exposed torsion springs you’ll find on most other brands. When that internal spring fails, the door gets heavy and the opener strains. We replace TorqueMaster assemblies with proper torque settings, not guesswork, and we show you the failed spring before quoting the replacement. Spring repair on these runs $180-$340.
- Foam-core panel delamination on the 9100 and 9600 series. Hollywood’s humidity and salt air work their way into the foam-filled panels over time, especially on doors facing east toward the ocean. The steel skin separates from the foam core, and the panel starts to look wavy. Panel replacement runs $250-$500 per panel, and we match the existing door’s profile so you’re not stuck with a mismatched section.
- Bottom seal rot and track corrosion on older 500-series doors. The 500 series was Wayne Dalton’s economy line, and the bottom retainer was prone to rusting through in coastal environments. Once the retainer goes, water and pests get under the door. We replace the retainer and seal as a unit, and when the track shows heavy pitting from salt exposure, we replace the track rather than dressing it up. Track realignment and replacement runs $120-$240.
- Hinge and roller wear on the 8300 and 8500 series. These mid-tier doors use standard hinges and rollers, but the hinge mounting points on the stiles are thinner than some competitors. In Hollywood garages where the door cycles five or six times a day, we see hinge tears at the stile. We address it before it rips out completely, and a full roller replacement runs $110-$220.
- Garage door opener incompatibility with older Wayne Dalton doors. We regularly see homeowners pair a newer smart opener with a Wayne Dalton door that’s too heavy for it, especially after years of spring fatigue. The opener’s logic board is pulling more amps than it should, and the door opens halfway before reversing. We measure the door’s actual weight and spring condition before recommending an opener, and we install LiftMaster, Chamberlain, and Genie openers alongside Wayne Dalton doors. Opener installation runs $250-$550.
Our Wayne Dalton Garage Door Installation Process
- 1
Measure and document. We come to your Hollywood home, measure the opening, check level and plumb, and photograph the existing door and hardware. You receive that photo record whether we do the work or not.
- 2
Written scope and price. Before any work starts, you get a flat price and a written scope of what’s included: door model, panel material, insulation value, hardware, track, springs, removal of the old door, and disposal. No verbal side notes.
- 3
Parts decision. We discuss OEM Wayne Dalton parts versus quality aftermarket equivalents where they exist. For TorqueMaster assemblies, we use OEM internals because the aftermarket versions don’t hold torque settings consistently. For hinges and rollers, quality aftermarket often outlasts OEM.
- 4
Installation day. We remove the old door, inspect the existing track and mounting points for hidden damage, install the new door, and set spring tension with a torque wrench so the door balances correctly. This isn’t a shortcut step; a misbalanced Wayne Dalton door kills openers.
- 5
Five-cycle minimum test. Marcus Deller’s standing rule: every door gets tested a minimum of five full cycles before the invoice closes. We watch for binding, noise, uneven travel, and opener strain on each cycle.
- 6
Final documentation. You get the photo record of what was installed, the written warranty, and the flat-price scope matching the invoice. If it’s not right, the 365-Day Done Right Promise means we make it right.
BeforeAfterWhat Wayne Dalton Garage Door Installation Costs in Hollywood
Here’s what we write on Hollywood quotes, straight from the price book:
- Single-car Wayne Dalton steel door, 8×7: $700-$1,200 installed
- Double-car Wayne Dalton steel door, 16×7: $1,200-$2,200 installed
- Insulated Wayne Dalton steel door (9100/9600 series), double-car: $1,400-$2,200 installed
- Spring repair (TorqueMaster or standard torsion): $180-$340
- Cable replacement: $130-$250
- Track realignment or replacement: $120-$240
- Panel replacement: $250-$500 per panel
What moves the price: door size, insulation level, whether the existing track and mounting points are reusable, removal and disposal of the old door, and any structural repair to the opening itself. Wood doors run higher, and custom sizes always cost more than stock. Every quote is flat and written, and the price you sign is the price you pay, not a starting point. Call (754) 465-7645 and we’ll come measure the opening and hand you a written number while we’re still on site.
Why Hollywood Homeowners Call Servo Garage Doors Hollywood for Wayne Dalton Work
We photograph the failed component before quoting a replacement. That’s not a sales tactic; it’s Clause 4 of The Haven Standard and the founding rule this company was built on in 2015. You see the broken TorqueMaster spring, the rusted track, the delaminated panel, before anyone asks you to spend a dollar. Then you get a written price. Then we do the work.
Our technicians are background-checked and uniformed, and the license is on the page, not buried. If you have a competing written estimate from another company, bring it in; the Free Second Opinion applies, no coupon required. We service all eight major brands, so if your Hollywood home has a LiftMaster opener on a Wayne Dalton door, one visit covers both. Name the part, quote the range, then do the work.
FAQs
Yes, we install customer-supplied Wayne Dalton doors in Hollywood with two conditions: the door must be new in box or verifiably unused, and we inspect it at the measure appointment before quoting labor. Starting at $700 for a standard single-car install, labor quote is written and flat before work starts. If the door arrives damaged from shipping, we document it and you deal with the seller before we proceed.
We’re an independent service provider, not a Wayne Dalton authorized dealer, so we don’t process manufacturer warranty claims on your behalf. What you get from us is the 365-Day Done Right Promise: if the installation isn’t right, we make it right, documented under The Haven Standard. For warranty coverage on the door itself, you’ll work with Wayne Dalton directly, and we’ll provide the installation documentation and photo record they typically require.
Most Wayne Dalton installations in Hollywood are completed within three to five business days of the measure appointment, which is typically scheduled within 48 hours of your call. Stock-size doors move faster; custom-spec doors depend on Wayne Dalton’s production lead time, which we quote in writing before you commit. For planning purposes, assume a full week from first call to finished door.
If the panels are structurally sound and the issue is springs, cables, rollers, or track, repair usually wins: those jobs run $110-$340 and extend the door’s life meaningfully. If you have delaminated foam panels, rust through the steel skin, or a door that’s sagging in the middle, replacement is the honest call. We’ll show you photos of what we found and give you both numbers before you decide.
We carry common Wayne Dalton parts in our Hollywood trucks: TorqueMaster springs, cables, hinges, rollers, and bottom seals for the 8000, 9000, and 9600 series. Special-order items, like full door sections or custom trim, are ordered after the measure and quoted in writing with the lead time. Call (754) 465-7645 for an exact quote, and the estimate is free.
Contact Servo Garage Doors Hollywood
If you need Wayne Dalton garage door installation in Hollywood, call us at (754) 465-7645. A live person answers, we schedule the measure, and you get a written price before anything turns. If you’re still comparing options, bring us another company’s written estimate and we’ll give you a free second opinion, straight up.
Written by Marcus Deller, Owner, Servo Garage Doors Hollywood at Servo Garage Doors Hollywood, serving Hollywood and nearby areas.